LordVader88 Posted November 14, 2019 Share Posted November 14, 2019 This was my 1st serious attempt at modding SK-S.E., so I did a fresh install, and followed the instructions as best I understood them. Overall I got most of them right I think. With MOD2, I was following Juanton's Skyrim Special Edition Mod List (2019)https://www.nexusmods.com/skyrimspecialedition/mods/23066 Thanks for the help, however that's a work in progress, and some steps aren't filled in at all. At the end I just stumbled through the wyrebash and Dynlod steps. I might have that messed up for sure. Right now it works, but I can't see my hands/weapons, I just hear the attack sound. NPC's are stuck in a T-pose and just slide around instead of walking. A torch light was pixelated and blurred. Who knows what else is wrong. I don't like the ENB, makes it way too dark, when I intsatlled it there was no options to choose from. If I can't set a brighter ENB, I don't want it at all. I have an i5-9600k, rtx 2070, 16GB ram, 155Hz panel, and it seems rather laggy so far, I don't need all these mods, it OTT. So call this a 1st try and getting used to modding in general. So can I just start disabling some mods ? Would I have to run things like loot, wyrebash, dynlod again ? Link to comment Share on other sites More sharing options...
Purr4me Posted November 14, 2019 Share Posted November 14, 2019 This was my 1st serious attempt at modding SK-S.E., so I did a fresh install, and followed the instructions as best I understood them. Overall I got most of them right I think. With MOD2, I was followingJuanton's Skyrim Special Edition Mod List (2019)https://www.nexusmods.com/skyrimspecialedition/mods/23066 Thanks for the help, however that's a work in progress, and some steps aren't filled in at all. At the end I just stumbled through the wyrebash and Dynlod steps. I might have that messed up for sure. Right now it works, but I can't see my hands/weapons, I just hear the attack sound. NPC's are stuck in a T-pose and just slide around instead of walking. A torch light was pixelated and blurred. Who knows what else is wrong. I don't like the ENB, makes it way too dark, when I intsatlled it there was no options to choose from. If I can't set a brighter ENB, I don't want it at all. I have an i5-9600k, rtx 2070, 16GB ram, 155Hz panel, and it seems rather laggy so far, I don't need all these mods, it OTT. So call this a 1st try and getting used to modding in general. So can I just start disabling some mods ? Would I have to run things like loot, wyrebash, dynlod again ?In my Forum signature, in the spoiler tag, there are 3 listings for Bethesda games dealing with skyrim modding, Please avail your self to the last / 3rd listing that shows all content concerning modding SSE games software.Start over. Do NOT use ENB until all errors are Eliminated. Your issue is this:you have incorrectly converted mods installed. Incompatible data is asserting it's self. "Improperly Converted mods from Old rim to new sse." Link to comment Share on other sites More sharing options...
Xahid Posted November 14, 2019 Share Posted November 14, 2019 When you're following the guide, its not necessary to follow them "exactly" you don't have to install the all Mods.from your post, I think you messed up with conflicting mods.you have to start with few Mods. and than add the mods you like at Nexus.MO2 already have loot plugin so no need to install separately I suggest, to remove all the mods, and try again with Few mods. Link to comment Share on other sites More sharing options...
LordVader88 Posted November 14, 2019 Author Share Posted November 14, 2019 Yeah I didn't install them all, but I sure never tested anything along the way. If I start over, and use LOOT as I go, when do I change the .ini files (there wasn't many changes), and use wyrebash and dynLOD ? To I do them each time ? Personally I want the overall visual upgrades to look good, like landscapes, caves, trees, towns, water, clutter, etc. To make it look like a 2019 game. Link to comment Share on other sites More sharing options...
LordVader88 Posted November 14, 2019 Author Share Posted November 14, 2019 (edited) OK I did this for clean installhttps://www.youtube.com/watch?v=ewUUS1xl2H0 And uninstalled MO2 , wryebash, LOOT. And deleted the left over MO2 directories. So I'll try again. Should go a lot smoother this time. I'm not using creation-club Edited November 14, 2019 by LordVader88 Link to comment Share on other sites More sharing options...
Xahid Posted November 16, 2019 Share Posted November 16, 2019 (edited) Its not the matter, how do you start, Just learn the different between Texture Mods and Mesh Mods, so you won't make mistakes for picking up the wrong Mod for you. If you don't want to learn about modding stuff (altho. it helps a lot for troubleshooting)just follow this guy... https://www.nexusmods.com/skyrimspecialedition/mods/23066 you'll be good to go. Edited November 16, 2019 by Xahid Link to comment Share on other sites More sharing options...
Grospolina Posted November 19, 2019 Share Posted November 19, 2019 just follow this guy... https://www.nexusmods.com/skyrimspecialedition/mods/23066 you'll be good to go.Are you sure that link is right? That's the same incomplete one that OP originally used. If you want a heavily-modded setup that works well, then you need to put in the work and test things along the way. Mod Organizer 2 gives you lots of tools for testing and troubleshooting. I get that you were just getting your feet wet, but now you know what bad things can happen. I suggest either installing Alternate Start - Live Another Life right away, or skipping the intro by opening the console (~) and typing "coc riverwood" from the main menu. Otherwise, you'll be going through the intro dozens of times. I suppose you could also save just after the intro and start from there. Link to comment Share on other sites More sharing options...
Xahid Posted November 20, 2019 Share Posted November 20, 2019 just follow this guy... https://www.nexusmods.com/skyrimspecialedition/mods/23066 you'll be good to go.Are you sure that link is right? That's the same incomplete one that OP originally used. If you want a heavily-modded setup that works well, then you need to put in the work and test things along the way. Mod Organizer 2 gives you lots of tools for testing and troubleshooting. I get that you were just getting your feet wet, but now you know what bad things can happen. I suggest either installing Alternate Start - Live Another Life right away, or skipping the intro by opening the console (~) and typing "coc riverwood" from the main menu. Otherwise, you'll be going through the intro dozens of times. I suppose you could also save just after the intro and start from there. lol, You are right.I think, he just messed up with conflicting mods. Link to comment Share on other sites More sharing options...
Recommended Posts