akifai Posted December 11, 2011 Share Posted December 11, 2011 @ throttlekitty Yes I have, I was able to edit the daedric helmet just fine, but that mesh didn't have any of these glow map stuff. As you can see, the armor is another issue. I'm pretty sure it's just a matter of adjusting some data within my mesh with nifskope to correspond with the original daedric armor, but I just don't know what to change. I hope someone can shed some light on my problem. Link to comment Share on other sites More sharing options...
Northborn Posted December 11, 2011 Share Posted December 11, 2011 I continue to be unable to add my new hood. I have: Created a custom GRUP (ARMO) and GRUP (ARMA) for it. The proper models should be set in the proper MOD2/3/4 sections. FormIDs are linked properly between ARMO and ARMA. If I try to use a model that's already ingame for the ARMA models, it works. But if I try to use my custom model, it does not appear ingame. The custom model, however, works fine when replacing another model via renaming them. I've very confused. Link to comment Share on other sites More sharing options...
Northborn Posted December 11, 2011 Share Posted December 11, 2011 Ah-ha! Needed to add 00 manually at the end of the HEX code for MOD2/3/4 I can't believe something so simple was at the source of the problem. Link to comment Share on other sites More sharing options...
throttlekitty Posted December 11, 2011 Share Posted December 11, 2011 @ throttlekitty Yes I have, I was able to edit the daedric helmet just fine, but that mesh didn't have any of these glow map stuff. As you can see, the armor is another issue. I'm pretty sure it's just a matter of adjusting some data within my mesh with nifskope to correspond with the original daedric armor, but I just don't know what to change. I hope someone can shed some light on my problem.If you have the same textures, EffectShaderProperty and AlphaProperty set, my other guess would be to make sure the glowing part still has vertex colors. Link to comment Share on other sites More sharing options...
akifai Posted December 11, 2011 Share Posted December 11, 2011 (edited) @ throttlekitty Thank you very much, you nailed it, that was the exact problem. When I exported the mesh, I didn't export the vertex colors. I went back to my edited mesh and re-exported everything with the vertex colors and everything is perfectly fine now. Thanks again. I really appreciate your help.....especially since I've been asking for help in other threads in this forum and your the only one who even bothered to try and help me. Take care. Edited December 11, 2011 by El Explosivo Link to comment Share on other sites More sharing options...
throttlekitty Posted December 11, 2011 Share Posted December 11, 2011 I really appreciate your help.....especially since I've been asking for help in other threads in this forum and your the only one who even bothered to try and help me. Take care.No problem, glad it worked :) But bad form, posting like that. :P Link to comment Share on other sites More sharing options...
Airahn Posted December 12, 2011 Share Posted December 12, 2011 So confused, I need help. Theoretically, if you texture an armor mesh, then set the MODL path in ARMA to the new mesh it should appear like that correct? Well, I've done this, and can't seem to do it correctly or something, because it just gives me invisible armor. So either I doing it wrong, or it isn't possible. Any advice from the kind community? Here's what I got, I am working on a non-replacer re-texture, everything matches up except for the invisible armor. Link to comment Share on other sites More sharing options...
Airahn Posted December 12, 2011 Share Posted December 12, 2011 (edited) So confused, I need help. Theoretically, if you texture an armor mesh, then set the MODL path in ARMA to the new mesh it should appear like that correct? Well, I've done this, and can't seem to do it correctly or something, because it just gives me invisible armor. So either I doing it wrong, or it isn't possible. Any advice from the kind community? Here's what I got, I am working on a non-replacer re-texture, everything matches up except for the invisible armor.Sorry, forgot the upload...I'm also sorry for the double post... Edited December 12, 2011 by Airahn Link to comment Share on other sites More sharing options...
joefantana Posted December 14, 2011 Share Posted December 14, 2011 (edited) so, thanks to this thread i been converting crap like a madman and my most recent one leads me to ask this question, is there a way to mirror a mesh in nifskope? here's a picture to see what i mean. thanks http://i846.photobucket.com/albums/ab27/ryujin_jaka/ScreenShot4.jpg Edited December 14, 2011 by joefantana Link to comment Share on other sites More sharing options...
Muncha Posted December 14, 2011 Share Posted December 14, 2011 Every time I try ti save my nif I get the message: "Link points to wrong block type!" http://img263.imageshack.us/img263/502/wrongblocktype.jpg I have no idea what that means. Link to comment Share on other sites More sharing options...
Recommended Posts